| Customization: | Available |
|---|---|
| Driving Mode: | Pneumatic |
| Connection Form: | Welding |
|
Still deciding? Get samples of US$ 12/Piece
Request Sample
|
Suppliers with verified business licenses
Audited Supplier Audited by an independent third-party inspection agency
| Standard | 3A,SMS,DIN,ISO,RJT,IDF | |
| Product wetted steel parts | AISI304/AISI316L | Provided with material inspection report |
| Other steel parts | AISI304 | |
| Size | 1/2"~6",DN10~DN150 | |
| Seal material | EPDM/VMQ/FPM | All seals material comply with FDA21CFR117.2600 |
| Working pressure | ≤10bar(145psi) | |
| Supply pressure for air actuator | 5~8(0~116psi) | |
| Working temperature | EPDM:-14~248ºF(-10~120ºC) | |
| VMQ:-58~356ºF(-50~180ºC) | ||
| FPM:22~446ºF(-30~230ºC) | ||
| Other materials are avaible upon request | ||
| Sterilization temperature | 302ºF(150ºC,max 20min) | |
| Outside surface treatment | Ra16~32uin(o.4~0.8um) | |
| Inside surface treatment | Ra32~64uin(o.8~1.6um) | |
| Connetion ends | butt-weld,clamped ends,male ends, flange ends | |
| Pneumatic head | Normally closed(NC)-Air to open,spring to close | |
| Normally open(NO)-Air to close,spring to open | ||
| Air to air(AA)-Air to open,air to close | ||
Options
1.The seat and gasket can be NBR (Nitrile), VMQ (Silicone) or Viton (FPM) all complying with FDA 21CFR177.2600.
2. End connection can be butt-welded, sanitary clamp, threaded, flanged, I-line or others upon request.
3.Handle: 3-position pull handle; multi-position handle in either pure stainless steel or with plastic cover.
4.Actuator: pneumatic stainless steel actuator (vertical type), pneumatic aluminum actuator (horizontal type), electric actuator.
5.Control: position sensor, C-top controller, C-top controller (AS-I)
Features
TPT pneumatic actuators are factory-lubricated for life to ensure a trouble-free service life and 1,000,000 cycles may be expected. However, this applies under ideal conditions. Under real conditions, the service life depends on several factors.
Contaminated air from air compressors and air supply system is the most common cause for shortened life service (solids, water, and oil). This contamination will gradually degrade and wash out the original grease lubricant. This will shorten the service life, therefore it will be almost impossible to accurately predict the service life.
If the compressed air supply is clean, dry and filtered to 40 micron, the grease will give the seals and components long life without adding oil through an oil mist lubricator.
Lubrication
The oil mist lubrication will extend the life of the actuator, but it will also wash out the original lubrication. Once begun, the oil mist lubrication cannot be discontinued and the lubricator should be regularly checked and maintained. If air lubricators are used, the lubricant selected must be compatible with Nitrile (Buna-N) seals.
Sealed and Unsealed Actuators
Our sealed actuators are maintenance free and our unsealed actuators are available for preventive/corrective maintenance. Life service of a pneumatic actuator is significantly extended only with a grease re-lubrication and replacement the O-ring seals.
How do I choose the right actuator for my application?
It depends on the number of operation cycles. For example, some actuators may perform hundreds of cycles per hour, whereas others open and close just once a day.
Please take a look at the chart below to make a decision.
| Cycles rate | Cycles per hour | Actuator recommended |
| Low | 1 to 5 | Sealed |
| Medium | 6 to 19 | Sealed / Unsealed |
| High | 20 to 30 | Unsealed |
Design Features
1.Various standards can be provided: DIN, 3A, SMS, ISO / IDF, BS / RJT, and ASME / BPE.
2.Available in sizes from DN25 / 1" to DN300 / 12"
3.Multiposition handles can be used for valves up to DN100 / 4";
4.Pull handles can be used for valves from DN25 / 1" to DN300 / 12"
Manual handle,
5.pneumatic actuator and electric actuator are interchangeable.
6.Seals comply with FDA 21CFR 177. 2600.
7.The valve body can be customized with a wide selection of different connections.
| 1. Samples: Buyer bear the air fee, but this fee will be reduced from order directly | |
| 2. Delivery: Never delay delivery time | |
| 3. Ensure material pure | |
| 4. After Sales: Please contact our After-sales service department in time within 30days after you received the cargo. Tel: 0086-0577-86995593,Working Time: 9:00 a.m.- 6:00 p.m. (Beijing time) | |
| Process | Please provide the copy of Sales Contract and describe the problems appeared. |
| Slight problem | Please send the proof to our After-Sales Department, we will reply within two days. |
| Serious problem |
a. We will dispatch our Quality and Problems Appraisers to make a confirmation |
| b. Have a negotiation of the compensation and sign agreements | |
| c. Our After-Sales Department will perform the duties as the agreements | |
| Replacement | Free replacement if there is any quality problem |
){kind=link}